most electronic bidets will be able
2020年1月2日 ペットBut these general China Across Wrench Suppliers guidelines will get you started. inches of space from the center of these caps to the front of the water tank.There are three main areas when it comes to installing your electronic bidet taking some measurements of your existing toilet, mounting the bidet and connecting to the existing cold water supply. This stops the water, preventing it from passing water through to the water tank. First, turn the valve to shut off the water intake.
Bidet Mounting Now that we have taken the necessary measurements and ordered the correct seat-type, its time to mount the bidet on the toilet. Turn the water supply back on, and check for leaks.5 inches to 18 inches, while elongated seats measure about 18 inches to 19.bidetsplus. Round seats typically measure 16. Behind your existing toilet seat youll find two caps, and underneath these caps are bolts which secure the toilet seat to the toilet.5 inches of space behind the caps of your toilet seat, and at least 5. Place the mounting bracket on top of these two holes, and then secure the bracket with the nuts and bolts which came included.
Now lets take one more measurement so we know which type of seat your bidet should come with a round seat or an elongated seat.The first measurement is the measurement in the back, where the rear of the bidet unit will sit. Additionally, since the bidet is attached to your toilet, you dont need a separate drainage system since the bidets water will just fall into the bowl.Modern electronic bidets are easy to install because they connect to the existing cold water supply which refills your toilets water tank.Water Supply Connection A water valve can be found behind Socket Sets Factory your toilet, with a hose connecting to the bottom of the water tank. Basin-type bidets are separate porcelain fixtures that sit next to the toilet and as such, may require a new drainage system and additional plumbing. All parts needed for installation will be included with your shipment.
If you would prefer to see a bidet installation video however, you can watch this tutorial: http://www. Measure the clearance from the center of these caps to the front of your water tank.The second measurement well need to take is the width between the caps behind your existing seat. Tighten all connections, using a wrench as necessary. Note: If you need help installing a basin-type bidet, please contact your local plumber.com/pages/Installation. Again, make sure youve closed the valve first or else youre going to get water everywhere!Now, find the metal T-connection which came included and secure it to the water valve. This article will show you the steps in installing a bidet attachment to your existing toilet.5 inches in width between the center of the two caps.Once the T-connection is secure, reconnect the hose to your water tank by fastening it to the top end of the T-connection.Lets remove your existing toilet seat by unscrewing the bolts underneath the caps we were measuring earlier. Starting from the caps behind your existing seat, take a measurement to the front of the bowl. Then secure a secondary hose (also included) to the T-connections remaining opening.htmlToilet Measurement Bidet measurements vary, so it is suggested that you refer to the product specification sheets for the model youre installing. On most bidet models, youll hear a click which indicates the bidet is properly secured. Then unscrew the hose and detach from the water valve. If your tank is curved, take that into consideration by measuring from the point of the water tank closest to the caps. After removing your seat, two holes will be visible which will be used to secure the mounting bracket. Most bidets will need at least. The other end of this hose will complete the connection to your bidet.Learning how to install a bidet is actually quite simple, and doesnt require any special skills. inches of width between the caps, then most electronic bidets will be able to fit your toilet.5 inches.Once the mounting bracket is properly fastened, the bidet will slide on and attach to your toilet.Each of these sections will be explained in detail below.5 inches of clearance all the way across the back.If you have at least 1. Confirm there is at least 1. Make sure there is at least 5. One of these parts will be the mounting bracket. Its called a T-connection because its shaped like the letter T and distributes the water in two different directions one way to your water tank, and the other way to the bidet.
Bidet Mounting Now that we have taken the necessary measurements and ordered the correct seat-type, its time to mount the bidet on the toilet. Turn the water supply back on, and check for leaks.5 inches to 18 inches, while elongated seats measure about 18 inches to 19.bidetsplus. Round seats typically measure 16. Behind your existing toilet seat youll find two caps, and underneath these caps are bolts which secure the toilet seat to the toilet.5 inches of space behind the caps of your toilet seat, and at least 5. Place the mounting bracket on top of these two holes, and then secure the bracket with the nuts and bolts which came included.
Now lets take one more measurement so we know which type of seat your bidet should come with a round seat or an elongated seat.The first measurement is the measurement in the back, where the rear of the bidet unit will sit. Additionally, since the bidet is attached to your toilet, you dont need a separate drainage system since the bidets water will just fall into the bowl.Modern electronic bidets are easy to install because they connect to the existing cold water supply which refills your toilets water tank.Water Supply Connection A water valve can be found behind Socket Sets Factory your toilet, with a hose connecting to the bottom of the water tank. Basin-type bidets are separate porcelain fixtures that sit next to the toilet and as such, may require a new drainage system and additional plumbing. All parts needed for installation will be included with your shipment.
If you would prefer to see a bidet installation video however, you can watch this tutorial: http://www. Measure the clearance from the center of these caps to the front of your water tank.The second measurement well need to take is the width between the caps behind your existing seat. Tighten all connections, using a wrench as necessary. Note: If you need help installing a basin-type bidet, please contact your local plumber.com/pages/Installation. Again, make sure youve closed the valve first or else youre going to get water everywhere!Now, find the metal T-connection which came included and secure it to the water valve. This article will show you the steps in installing a bidet attachment to your existing toilet.5 inches in width between the center of the two caps.Once the T-connection is secure, reconnect the hose to your water tank by fastening it to the top end of the T-connection.Lets remove your existing toilet seat by unscrewing the bolts underneath the caps we were measuring earlier. Starting from the caps behind your existing seat, take a measurement to the front of the bowl. Then secure a secondary hose (also included) to the T-connections remaining opening.htmlToilet Measurement Bidet measurements vary, so it is suggested that you refer to the product specification sheets for the model youre installing. On most bidet models, youll hear a click which indicates the bidet is properly secured. Then unscrew the hose and detach from the water valve. If your tank is curved, take that into consideration by measuring from the point of the water tank closest to the caps. After removing your seat, two holes will be visible which will be used to secure the mounting bracket. Most bidets will need at least. The other end of this hose will complete the connection to your bidet.Learning how to install a bidet is actually quite simple, and doesnt require any special skills. inches of width between the caps, then most electronic bidets will be able to fit your toilet.5 inches.Once the mounting bracket is properly fastened, the bidet will slide on and attach to your toilet.Each of these sections will be explained in detail below.5 inches of clearance all the way across the back.If you have at least 1. Confirm there is at least 1. Make sure there is at least 5. One of these parts will be the mounting bracket. Its called a T-connection because its shaped like the letter T and distributes the water in two different directions one way to your water tank, and the other way to the bidet.
コメント